选区激光熔化工艺参数对气雾化316L不锈钢粉末成形制品性能的影响

本研究系统考察了激光功率和扫描速度对316L不锈钢粉末选区激光熔化工艺成形熔道、制品微观组织及力学性能的影响,并分析了各类缺陷的形成原因。研究结果表明:在低激光功率和高扫描速度条件下,熔道中出现了大量球状颗粒,这些颗粒之间的空隙恶化了下一层粉末的熔化条件,这正是成形制品中熔道分布混乱以及孔洞、裂纹产生的根本原因,进而导致成形制品力学性能降低;在高激光功率和低扫描速度条件下,熔池快速升温/冷却的热应力作用增强,使得成形制品的熔道交界处也存在孔洞和裂纹等缺陷。在本研究实验条件下,激光功率为350 W,扫描速度为1750 mm/s时,SLM成形制品的力学性能最为优异,其中抗拉强度为731 MPa、屈服强度为638 MPa、断后伸长率为40.0%,致密度为96.27%。     

Exploiting Bayesian networks for fault isolation: A diagnostic case study of diesel fuel injection system

Fault isolation is known to be a challenging problem in machinery troubleshooting. It is not only because the isolation of multiple faults contains considerable number of uncertainties due to the strong correlation and coupling between different faults, but often massive prior knowledge is needed as well. This paper presents a Bayesian network-based approach for fault isolation in the presence of the uncertainties. Various faults and symptoms are parameterized using state variables, or the so-called nodes in Bayesian networks (BNs). Probabilistically causality between a fault and a symptom and its quantization are described respectively by a directed edge and conditional probability. To reduce the qualitative and quantitative knowledge needed, particular considerations are given to the simplification of Bayesian networks structures and conditional probability expressions using rough sets and noisy-OR/MAX model, respectively. By adopting the simplified approach, symptoms under multiple-fault are decoupled into the ones under every single fault, while the quantity of the conditional probabilities is simplified into the linear form of the faults quantity. Prior knowledge needed in Bayesian network-based diagnostic model is reduced significantly, which decreases the complexity in establishing and applying this diagnosis model. The computational efficiency is improved accordingly in the simplified BN model, after eliminating the redundant symptoms. The fault isolation methodology is illustrated through an example of diesel engine fuel injection system to verify the developed model.     

3D printing hybrid organometallic polymer‐based biomaterials via laser two‐photon polymerization

Materials with microscale structures are gaining increasing interest due to their range of technical and medical applications. Additive manufacturing approaches to such objects via laser two‐photon polymerization, also known as multiphoton fabrication, enable the creation of new materials with diverse and tunable properties. Here, we investigate the properties of 3D structures composed of organometallic polymers incorporating aluminium, titanium, vanadium and zirconium. The organometallic polymer‐based materials were analysed using a variety of techniques including SEM, energy‐dispersive X‐ray spectroscopy, X‐ray photoelectron spectroscopy analysis and contact angle measurements and their biocompatibility was tested in vitro. Cell viability and mode of death were determined by 3‐(4,5‐dimethyl‐2‐thiazolyl)‐2,5‐diphenyl‐2H‐tetrazolium bromide (MTT) assay and acridine orange/ethidium bromide staining. Polymers incorporating Al, Ti and Zr supported cell adhesion and proliferation, and showed low toxicity in vitro, whereas the organometallic polymer incorporating V was shown to be cytotoxic. Inductively coupled plasma optical emission spectrometry suggested that leaching of the V from the organometallic polymer is the likely cause of this. The preparation of the organometallic polymers is straightforward and both simple 2D and complex 3D structures can be fabricated with ease. Resolution tests of the newly developed organometallic polymer incorporating Al show that suspended lines with widths down to 200 nm can be fabricated. We believe that the materials described in this work show promising properties for the development of objects with sub‐micron features for biomedical applications (e.g. biosensors, drug delivery devices, tissue scaffolds etc.). © 2019 The Authors. Polymer International published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.     

压水堆核电厂采用富集硼的优势与可行性分析

压水堆核电厂通常采用天然硼进行反应性的化学补偿控制,研究表明采用富集硼替代天然硼,可以优化一回路水化学,降低一回路结构材料腐蚀风险和堆芯沉积风险,降低职业照射剂量。本文分析压水堆核电厂采用富集硼的优势与可行性,介绍国内外核电厂富集硼的应用情况。最后对我国华龙一号堆型和在役压水堆核电厂富集硼的应用提出建议。     

Evolution of properties of parts during MIM and sintering of recycled oxide particles

Metal injection moulding (MIM) is an established process for high volume production of complex shaped metallic parts using commercially available feedstocks. The characteristics of parts after moulding, debinding, and sintering cannot be simply predictable from raw materials because the properties get altered with the process parameters and the corresponding levels of porosity during processing steps. In this study, physical properties, microstructure, and mechanical properties of the MIM parts have been characterised to understand the evolution of strength during various steps in MIM processing. Feedstocks with different binder loading show a considerable difference in physical as well as mechanical characteristics. During sintering of parts which have solid loading of grinding sludge, simultaneous in situ reduction and densification takes place, whereas only densification occurs in carbonyl iron parts. It is, therefore, possible to make complex shaped parts of different levels of porosity from downgraded shop floor metallic waste.     

固体自拉曼激光器多波长输出研究

实验对比了a切和c切的Nd∶YVO4晶体作为激光晶体时,激光器输出光光谱及输出功率上的区别。设计了一种小型化固体自拉曼多波长激光器,实验证明通过调节倍频晶体BBO的角度,可实现多波长选择性输出及同时输出,并测量了其输出光谱及单波长输出时的功率。     

Low-threshold lasing in a plasmonic laser using nanoplate InGaN/GaN

Plasmonic nanolaser as a new type of ultra-small laser,has gain wide interests due to its breaking diffraction limit of light and fast carrier dynamics characters.Normally,the main problem that need to be solved for plasmonic nanolaser is high loss induced by optical and ohmic losses,which leads to the low quality factor.In this work,InGaN/GaN nanoplate plasmonic nanolaser with large interface area were designed and fabricated,where the overlap between SPs and excitons can be en-hanced.The lasing threshold is calculated to be ～6.36 kW/cm2,where the full width at half maximum (FWHM) drops from 27 to 4 nm.And the fast decay time at 502 nm (sharp peak of stimulated lasing) is estimated to be 0.42 ns.Enhanced lasing charac-ters are mainly attributed to the strong confinement of electromagnetic wave in the low refractive index material,which im-prove the near field coupling between SPs and excitons.Such plasmonic laser should be useful in data storage applications,bio-logical application,light communication,especially for optoelectronic devices integrated into a system on a chip.     

Mitochondrial Bioenergetic,Photobiomodulation and Trigeminal Branches Nerve Damage,What’s the Connection? A Review

Background: Injury of the trigeminal nerve in oral and maxillofacial surgery can occur. Schwann cell mitochondria are regulators in the development, maintenance and regeneration of peripheral nerve axons. Evidence shows that after the nerve injury, mitochondrial bioenergetic dysfunction occurs and is associated with pain, neuropathy and nerve regeneration deficit. A challenge for research is to individuate new therapies able to normalise mitochondrial and energetic metabolism to aid nerve recovery after damage. Photobiomodulation therapy can be an interesting candidate, because it is a technique involving cell manipulation through the photonic energy of a non-ionising light source (visible and NIR light), which produces a nonthermal therapeutic effect on the stressed tissue. Methods: The review was based on the following questions: (1) Can photo-biomodulation by red and NIR light affect mitochondrial bioenergetics? (2) Can photobiomodulation support damage to the trigeminal nerve branches? (preclinical and clinical studies), and, if yes, (3) What is the best photobiomodulatory therapy for the recovery of the trigeminal nerve branches? The papers were searched using the PubMed, Scopus and Cochrane databases. This review followed the ARRIVE-2.0, PRISMA and Cochrane RoB-2 guidelines. Results and conclusions: The reliability of photobiomodulatory event strongly bases on biological and physical-chemical evidence. Its principal player is the mitochondrion, whether its cytochromes are directly involved as a photoacceptor or indirectly through a vibrational and energetic variation of bound water: water as the photoacceptor. The 808-nm and 100 J/cm² (0.07 W; 2.5 W/cm²; pulsed 50 Hz; 27 J per point; 80 s) on rats and 800-nm and 0.2 W/cm² (0.2 W; 12 J/cm²; 12 J per point; 60 s, CW) on humans resulted as trustworthy therapies, which could be supported by extensive studies.